Vandal Resistant Push Button Switch AVP19FWM1S - Local stock & specs

Overview

The AVP19FWM1S vandal-resistant push button switch is a compact, metal-bodied momentary switch designed for tamper-resistant front-panel use in kiosks, access panels, instrumentation and hobbyist enclosures. This landing page summarises the key specifications, compatibility notes, accessory options and local availability considerations for builders and engineers in South Africa.

Key specification callouts

• Mounting: panel cutout typically 19 mm (confirm with datasheet and drill template).
• Actuation: momentary (push-to-make) with a vandal-resistant stainless steel bezel.
• Contact configuration: commonly single-pole single-throw (SPST) or SPDT variants - confirm model suffix for exact contacts.
• Electrical ratings: low-voltage DC switching for control circuits; check product page for exact current/voltage ratings.
• Termination: solder lugs or PCB pins depending on version; some variants accept wire crimp terminals.

Why choose a vandal-resistant switch?

Vandal-resistant switches have a hardened bezel and raised or recessed actuator to reduce tampering, making them suitable for public-facing installations. For South African deployments (schools, makerspaces, public kiosks), this improves longevity in high-traffic locations and reduces unplanned maintenance.

Local availability, lead times and branches

Communica stocks a broad range of electromechanical parts and can often supply vandal-resistant push buttons from makers and industrial suppliers. Check stock and branch pickup options to avoid lead-time delays; Samrand is the primary warehouse for most business orders. For branch hours and collection, see Branches & Trading Hours.

Compatibility and use cases

The AVP19FWM1S is commonly used as a user input button for microcontroller projects (Arduino, Raspberry Pi), relay control panels, reset switches and emergency-stop style inputs where a momentary action is required. Verify the contact rating before switching loads directly; for higher-current circuits use the switch to drive a relay or MOSFET.

For browsing similar components and accessories, view Communica's product collections at electronic components for DIY projects and robotics and brands at Shop by Brand.

Simple mounting and wiring diagram

Typical panel mounting requires a 19 mm hole and a nut to secure the bezel. Wiring depends on termination type; below is an ASCII wiring example for an SPST normally open (NO) momentary switch used to trigger a microcontroller input with a pull-down resistor.

  +3.3V ---[pull-up]--- MCU INPUT
                      |
                   [SW]  <-- AVP19FWM1S (NO)
                      |
                     GND

If the panel cutout or bezel is different, measure the bezel diameter and consult the product datasheet before drilling. For general company background and distribution footprint, see About Communica.

Specification Callouts and Accessories

When specifying the AVP19FWM1S for a project, record the exact contact configuration, electrical rating (VDC/VAC and maximum current), actuator style and termination. Communica lists compatible accessories such as sealing gaskets, locking nuts, protective caps and matching wiring harnesses in the collections index - browse related parts at All Products.

Compatibility guidance and accessory bundles

• If switching >1 A, use the switch to drive a relay or a suitably-rated solid-state switch.
• Match termination style: choose PCB-pin versions for crowded boards, solder-lug or crimp options for panel harnesses.
• Consider an IP gasket or O-ring for outdoor enclosures; check the product variant's seal options.

Specification comparison

Compatibility example and calculations

If you need to drive a 12 V lamp drawing 2 A, do not switch the lamp directly if the switch's rated current is lower. Instead use a relay. Example calculation using Ohm's law and power:

Ohm's law: V = I × R. Power dissipated: P = V × I. For a 12 V load at 2 A, the lamp draws 24 W. Ensure the switching device and wiring are rated above that power; for safety choose components rated for at least 30% higher than expected load (example guideline).

Branch orders, VAT invoices and procurement notes

For education and institutional procurement, Communica can provide VAT invoices and account quotes. Check real-time stock or reserve items for collection at Samrand to avoid lead-time issues, especially for bulk orders. For hours and branch collection options, refer to ip65-rated-vandal-resistant-switches-for-outdoor-use (same link as earlier for convenience).

Requesting quotes and next steps

If you need a formal quote for AVP19FWM1S parts or an accessory bundle (gaskets, nuts, harnesses), Communica's sales team can prepare account pricing and delivery options from the Samrand warehouse. For company background and distribution reach, visit electronic-components-for-diy-projects-and-robotics.

Sources

• Communica - Homepage
• Communica - About Us
• Communica - Branches & Trading Hours